TODO
Jump to navigation
Jump to search
TODO
Take apart rear | 10 | |
![]() |
Change battery hold-down system in boot | 40 |
![]() |
Mount inverter replace rear bolts |
2 |
Make better fuse mount for boot battery box | 10 | |
Repackage BMS on battery in the boot | 25 | |
![]() |
Design & fabricate front battery box and mounting system | ? |
![]() |
Install traction cable Protect traction cable at entry boot Improve hangers Shorten cable Make motor junction box |
10 10 3 20 |
Take apart front | 10 | |
![]() |
Motor mounts Talk to certifier Weld front mount Remake rear mount Remake left mount |
2 30 10 |
Move left brake hose | 10 | |
Clean up front subframe | 40 | |
Reassemble front | 12 | |
Paint rear welds reassemble rear |
10 20 | |
Build battery box for rear seat | ||
Adjust brake light switch | ||
Check brake lights come on before regen | ||
![]() |
Cooling System | |
![]() |
Improve Throttle Pedal installation. Need 2 1/4" UNF 1/4 bolt. | |
![]() |
Make speedo work | |
Put together charger control box | ||
![]() |
Write BMS Software | |
Tidy up scratches in underbody paint | ||
Locate and install Air Conditioning components | ||
Clean & paint front subframe | ||
Tidy up High Voltage Wiring | ||
Select Charging Plug | ||
Design and make Charging Plug arrangement on body | ||
Repackage Air Conditioning inverter | ||
Remove unnecessary gears | ||
![]() |
Mount charger | |
![]() |
Sort out restraint system | |
![]() |
Connect direction switch | |
![]() |
Mount Aux Battery | |
![]() |
Mount contactors | |
![]() |
Replace tyre | |
![]() |
Repair puncture | |
![]() |
KillaCycle Down Under 2010 | |
![]() |
LCA2010 | |
![]() |
Bleed Brakes | |
![]() |
Write presentation | |
![]() |
Mount EVision shunt and brains | |
![]() |
Connect contactor box | |
![]() |
Tighten traction connections | |
![]() |
Secure traction cables | |
![]() |
Fabricate inverter brackets | |
![]() |
Charge auxiliary battery | |
![]() |
Redesign & fabricate motor mounts | |
![]() |
Improve rear battery box compression | |
![]() |
Pack rear battery box | |
![]() |
Tidy up low voltage wiring | |
![]() |
Reassemble and reinstall rear subframe | |
![]() |
Improve charging plug adapter | |
![]() |
Acquire 10A circuit breaker | |
![]() |
Acquire RCD | |
![]() |
Clean and paint rust above rear subframe | |
![]() |
Clean and paint rear battery box | |
![]() |
Acquire kWh meter | |
![]() |
Clean & paint rear subframe | |
![]() |
Fix EVision serial port | |
![]() |
Acquire Air Conditioning compressor | |
![]() |
Move inverter | |
![]() |
Connect speed signal to EVision | |
![]() |
Bring EVision serial port into cabin | |
![]() |
Mount regen sensor | |
![]() |
Bleed brakes | |
![]() |
Mount EVision in dashboard | |
![]() |
Install battery cover | |
![]() |
Mount brake master cylinder | |
![]() |
Make motor torque arm | |
![]() |
Connect handbrake | |
![]() |
Mount Fuse | |
![]() |
Mount contactor box | |
![]() |
Mount inverter | |
![]() |
Install Driveshafts | |
![]() |
Install motor & gearbox | |
![]() |
Install front subframe | |
![]() |
Install adjustable front suspension | |
![]() |
Install rear subframe | |
![]() |
Fabricate battery hold downs | |
![]() |
Fettle adapter plate | |
![]() |
Build gearbox | |
![]() |
Respline driveshafts | |
![]() |
Measure driveshafts | |
![]() |
Make motor mounts | |
![]() |
Install adjustable rear suspension | |
![]() |
Fold lip on and install rear battery box | |
![]() |
Brake Pipes | |
![]() |
Throttle Pedal |